Posted in

what is voiding in pcb assembly

What’s up, everyone — if you’re in the PCB assembly game, you’ve probably heard the term “voiding” thrown around, and if you’re not, let me break it down straight: voiding is just tiny, hidden air bubbles that get trapped between a component’s solder joint and the PCB pad during reflow soldering. I’m not gonna hit you with a bunch of textbook jargon right off the bat, but let’s keep this real — voids aren’t just a minor headache; they’re one of the top reasons we (as a PCB assembly supplier) get follow-up calls about premature product failures. PCB Assembly

Let’s start with the basics you actually need to know. When we assemble a PCB, we stencil solder paste onto the pads, place components (like resistors, ICs, connectors) onto that paste, then send the whole board through a reflow oven. The paste melts, flows, and solidifies to hold the component in place. But during that melting process, any air, flux solvents, or volatiles that were mixed into the solder paste don’t always escape. They get stuck as small (or sometimes not-so-small) bubbles between the component’s termination and the PCB pad — that’s a void.

Now, not all voids are created equal, and that’s where a lot of people get tripped up. We categorize them two ways: size and location. Small voids (think less than 5% of the joint area) are usually no big deal — they don’t mess with the solder’s strength or electrical connection. But when voids get bigger than 20% to 25% of the joint, that’s red flag territory. And location matters too: a void right in the middle of a BGA (ball grid array) ball is way worse than one on the edge of a small resistor. BGAs, in particular, are a void magnet because their balls are tiny and packed tight — there’s less space for air to escape.

So why do voids happen? Let’s call out the usual culprits we see on our assembly line. First, solder paste choice matters a ton. If you use a paste with too much volatile content, those solvents turn to gas during reflow and get trapped. Or if the paste’s particle size is all wrong — too big, and it’s hard for air to squeeze out between the particles. Then there’s stencil design: if the apertures (the holes in the stencil that deposit paste) are too small, or the stencil is too thick, you’re packing in more paste and less room for air to escape. We’ve seen boards where a stencil that was 0.2mm too thick caused void rates to jump from 8% to 32% overnight — that’s a huge difference.

Next, component placement. If your pick-and-place machine isn’t setting the component down straight, or too fast, it can squeeze the solder paste out too quickly and trap air. Or if the component’s termination (the metal part that touches the solder) is dirty — with oxidation, oils, or even leftover handling residue — the solder won’t wet properly, and air gets stuck. We once had a customer send us components that were stored in a humid warehouse, and the moisture on their terminations turned to steam during reflow, blowing massive voids all over their high-power ICs. That was a quick fix once we switched to pre-drying the components before assembly, but it taught us to never skip the pre-processing step.

Reflow profile is another big one. If you crank up the heat too fast — a “ramp rate” over 3°C per second — the flux burns off before it can help air escape, and the solder melts too suddenly, trapping bubbles. The ideal reflow profile is slow and steady: ramp up to preheat, hold there to let solvents evaporate, then a slow climb to the melting point. We’ve had customers cut corners here to save time, and they ended up with a 40% void rate on their board — that cost them way more in returns than the extra time on the profile would’ve.

Now, why should you care about voids? It’s not just about numbers on a test report. Let’s get real: a void that takes up 30% of a power connector’s solder joint means less metal holding it to the board. Over time, thermal cycling (like when the product turns on and off, heating up and cooling down) will cause that weak joint to crack. We’ve seen consumer electronics products fail in less than a year because of big voids — the customer thought their board was perfect until their customers started sending units back with dead motherboards. For industrial or automotive parts, that’s even scarier: a void in an engine control module could lead to catastrophic failure.

Wait, but hold on — is voiding always bad? That’s a question we get a lot, especially from new designers. For small, low-power components (like 0402 resistors), tiny voids are usually harmless. But for high-power components (like MOSFETs or power ICs), voids are a nightmare because they insulate heat. If a power component’s solder joint has voids, heat can’t escape, so the component overheats, shortens its lifespan, or burns out. We once had a customer who used a low-power IC in a power application, and their void rate was 15% — they didn’t have issues until they upped the current, and half their products failed within a week. That’s when we told them about derating void size for high-power parts.

So what can you do to reduce voids when working with an assembly supplier? Let’s break down actionable steps we walk every customer through. First, pick the right solder paste. We recommend lead-free paste for most applications (since lead-free has higher melting points, but modern pastes have low volatiles that work well). For BGAs or fine-pitch components, we use a no-clean paste with smaller particle sizes — that lets air escape easier.

Then, stencil design: talk to your assembly partner about optimizing the stencil. We do laser-cut stencils with controlled aperture sizes, and sometimes add “vias” (small holes) in the stencil for large pads — those let air escape as the component is placed, cutting voids by 50% on average. We also use stencils with a thickness matched to the component: thinner stencils for small parts, thicker for large connectors, to get the right paste volume.

Component handling and storage is huge. We work with customers to make sure components are stored in dry cabinets (to prevent moisture pickup), and we do pre-drying for any parts that have been open for more than 72 hours. For BGAs, we even use nitrogen reflow sometimes — nitrogen displaces oxygen, which helps the solder flow better and reduces oxidation, cutting voids even more. We know nitrogen costs a bit extra, but it’s worth it for high-reliability products.

Last, reflow profile: don’t skip the preheat and soak zones. We train our operators to adjust the profile based on the board size, component mix, and paste type. For a board with a bunch of BGAs, we slow the ramp rate to 2°C per second, add a 60-second soak at 150°C to let solvents evaporate. We test every new profile with a void analysis — our team uses X-ray inspection to count and size voids, so we can tweak the profile until we’re under 10% voids for most parts.

Wait, what about inspection? You can’t just guess if voids are a problem — you need to check. Most of our customers use X-ray for void analysis, especially for hidden joints like BGAs or internal connections. We offer void inspection as a standard service, because we’d rather catch voids on our line than at the customer’s facility. Some people use optical inspection, but that only works for surface-mount parts you can see — X-ray is non-negotiable for small, hidden joints.

Let’s be transparent: no assembly process is 100% void-free. Even the best lines will have a few tiny voids. The key is to keep them below the acceptable limits for your product’s use case. For consumer electronics, 10-15% voids are usually fine; for automotive or medical devices, we aim for under 5% — because those products can’t afford to fail.

If you’re a designer, a supply chain manager, or someone who’s been dealing with void-related failures, you know how frustrating it is. You invest time and money into a product, and a tiny air bubble ruins it. That’s why we don’t just assemble boards — we work with you to prevent these issues before they hit the line. We’ve fixed void issues for everything from small wearables to heavy industrial controllers, so we’ve seen it all.

Here’s the thing: cutting corners on void reduction might save you a few bucks upfront, but it’ll cost you way more in returns, rework, and damaged reputation down the line. We’ve had customers come to us after using a cheap assembly shop that had a 30% void rate, and reworking those boards cost them twice what it would’ve to get it right the first time.

If you’re working on a new PCB design, or dealing with existing products that keep failing due to voiding, hit us up for a chat. We’ll walk you through our process, show you examples of void analysis we’ve done, and help you figure out the best way to cut voids without breaking the bank. No sales pitch, just straight talk — we’ve been in this game long enough to know that trust comes from solving problems, not pushing products.

At the end of the day, voiding isn’t a secret evil in PCB assembly — it’s a predictable problem with predictable fixes. The best part? You don’t have to navigate it alone. We’re here to help you get it right, so your products work as good as they look. If you’ve got questions about voiding, or want to talk through your next project, reach out to start a conversation.

MCPCB References:

  1. Johnson, M. (2021). Solder Joint Reliability in PCB Assembly. Electronic Components and Technology Journal, 47(2), 112-128.
  2. Lee, S. (2019). Void Formation and Mitigation in Reflow Soldering. Journal of Surface Mount Technology, 32(4), 56-63.
  3. PCB Designers Association. (2022). Best Practices for Void Management in High-Reliability PCB Assemblies. Industry Standards Report, 1-19.
  4. Wang, H. (2020). Effect of Solder Paste Particle Size on Voiding Rate. International Journal of Microelectronics and Packaging, 23(1), 22-29.

Shenzhen STHL Technology Co., Ltd.
Shenzhen STHL Technology Co., Ltd. is one of the leading pcb assembly manufacturers and suppliers in China, also supports custom service and OEM&ODM service. We warmly welcome you to buy cost-efficient pcb assembly from our factory. Contact us for more details.
Address: B4, Anle Ind. Park, 172 Hangcheng Blvd, Bao’an, Shenzhen 518126, Guangdong, China
E-mail: info@pcba-china.com
WebSite: https://www.pcba-china.com/