Posted in

How to use a cord end crimper

If you work in electrical assembly, industrial wiring, or even automotive repair, you know how important properly terminated cord ends are. A loose, poorly crimped connection can lead to signal loss, overheating, or even safety hazards down the line. For years, I’ve supplied cord ends to small repair shops and large industrial facilities alike, and one question I get more than any other is: “How do I make sure my cord end crimps are strong and reliable?” I’ve seen too many techs rush the crimping process and end up with connections that fail after just a few weeks of use. That’s why I put together this step-by-step guide to using a cord end crimper correctly, from prepping your materials to testing your finished connection. Cord End

First, let’s start with the basics: what a cord end crimper does, and why it’s not a one-size-fits-all tool. Cord ends (also called ferrules or wire end sleeves) are small metal tubes that slide onto the end of a stranded wire. They crimp down to hold the wire strands tightly together, then connect to a terminal block, breaker, or other component. A good crimp creates a gas-tight connection that distributes electrical current evenly, preventing hot spots that can melt insulation or cause fires. The crimper is the tool that applies pressure to the ferrule—different crimpers are designed for different ferrule sizes, wire gauges, and crimp styles (insulated vs. non-insulated ferrules, for example). If you use a crimper that’s too big for your ferrule, you won’t get enough pressure to secure the wire; too small, and you’ll deform the ferrule so it can’t slide into the terminal.

When I work with new customers, the first tip I always give is to match your crimper to your cord ends and wire. Let’s break that down: if you’re using an insulated cord end (the plastic sleeve on the outside makes identifying gauge easier), you’ll need a crimper with a separate die for the insulated part and the metal ferrule. For non-insulated ferrules (common in industrial settings where space is tight), you need a die designed to crimp just the metal tube without damaging the wire inside. I always tell folks to check their crimper’s manual or the label on the tool to confirm it’s rated for the wire gauge and ferrule size they’re using. A common mistake I see is someone grabbing a crimper they had for a 16-gauge wire and trying to use it on 10-gauge—this leads to weak crimps every time.

Now, let’s walk through the step-by-step process, starting with prep work that’s easy to skip but makes all the difference. First, gather your materials: your cord end (ferrule), the stranded wire you’re terminating, your cord end crimper, wire strippers, and a rag to wipe away debris. The first step is stripping the wire correctly. Too many techs strip too much insulation, which leaves wire strands sticking out past the ferrule, or too little, which means the ferrule won’t grip the strands. For most stranded wires, you want to strip about 1/8 inch to 1/4 inch of insulation off the end—just enough to slide the ferrule over the bare wire strands. Once you strip the insulation, gently twist the wire strands together so they’re neat, no frayed ends sticking out. If the strands are loose, the ferrule won’t hold them tightly, leading to a bad crimp. If you have extra frayed strands, snip them with a small pair of scissors before sliding on the ferrule.

Next, slide the ferrule onto the wire. Make sure the bare wire is all the way inside the metal ferrule—no strands peeking out the end of the ferrule, and no insulation inside the ferrule (insulation inside the ferrule prevents a solid connection). If you’re using an insulated cord end, the bare wire should sit right at the edge of the metal sleeve, just below the plastic insulation of the ferrule. Once the ferrule is in place, it’s time to position it in the crimper. This is where alignment matters most. Most crimpers have marks on the dies to show where the ferrule should sit. For a non-insulated ferrule, you want the ferrule centered in the crimp die, so the pressure is applied evenly around the entire tube. If you’re using an insulated ferrule, you’ll align the plastic shoulder of the ferrule with the edge of the insulated die on the crimper. If the ferrule is off-center, one side will be crimped tighter than the other, leading to a weak spot that can break over time.

Now, the crimping itself. Squeeze the crimper handles firmly and hold them closed for 2 to 3 seconds. A lot of people will give a quick squeeze and let go, but that’s not enough to compress the ferrule properly. The pressure needs to be consistent all the way around the ferrule to deform it into a shape that grips the wire strands tightly. If your crimper has a ratchet mechanism, make sure you let it complete the full cycle—don’t force it open halfway. Ratchet crimpers are designed to ensure you apply the right amount of pressure, so forcing them can damage the tool or lead to an uneven crimp. If you’re using a manual crimper without a ratchet, test the pressure first on a scrap ferrule of the same size to make sure you’re not squeezing too hard or too soft.

Once you’ve crimped the ferrule, it’s time to inspect and test your work. The visual check is quick: the ferrule should be uniform in shape, no gaps between the metal and the wire. If you used an insulated ferrule, the plastic cover should be intact, no cracks from the crimper. Next, do a pull test: grab the wire near the insulation and pull firmly on the ferrule. A good crimp won’t pull the ferrule off the wire, and the wire strands won’t come loose inside the ferrule. If the ferrule pulls off easily, you either stripped too much insulation, didn’t seat the ferrule all the way, or used the wrong crimper size. Another test is the bend test: gently bend the wire back and forth near the crimp. If the crimp holds without breaking the wire strands or deforming the ferrule, that’s a solid connection. I always tell customers to do this test on every crimp—don’t skip it, even if you’re crimping dozens of the same size. I’ve had multiple folks come back saying a batch of crimps failed, and when we checked, they skipped the pull test and had used the wrong die size for their ferrules.

Now, let’s talk about common mistakes I see regularly, so you can avoid them. First, using the wrong crimper. A lot of people will buy a cheap multi-tool crimper that does everything from coax connectors to cord ends, but those are rarely precise enough for reliable crimps. Investing in a crimper specifically rated for cord ends will save you time and money in the long run. Second, over-stripping the wire. If you strip too much insulation, the ferrule can’t grip the insulation as well, leading to the ferrule pulling away from the wire under tension. Third, frayed wire strands. Stranded wires fray easily, so take an extra 10 seconds to twist the strands together before sliding on the ferrule. Frayed strands mean loose connections, which can cause overheating. Fourth, not maintaining your crimper. Dirt, debris, and rust can build up on the dies over time, leading to uneven crimps. Wipe your crimper dies with a rag after each use, and occasionally use a small wire brush to remove any metal shavings from crimping. If the dies are damaged or worn, replace them—worn dies can’t apply the right pressure to the ferrule.

I also want to touch on different types of cord ends and crimpers, because not all applications are the same. For residential electrical work, insulated cord ends are common because they add a layer of safety, preventing accidental contact with live parts. For industrial machinery or automotive wiring, non-insulated ferrules are often preferred because they’re smaller, fit into tight terminal blocks, and provide a more solid connection. If you’re working in a high-vibration environment (like construction equipment or marine wiring), you’ll want a heavy-duty crimper designed to create a cold weld crimp, which is stronger than a standard crimp and resists coming loose over time. I supply both insulated and non-insulated cord ends, and I always recommend matching the ferrule size to your wire gauge—every ferrule is labeled with a wire gauge range, so double-check that before you buy.

Another thing to keep in mind: working with stranded vs. solid wire. The steps are almost the same, but for solid wire, you don’t have to twist strands together as much, since there’s no fraying. For stranded wire, though, twisting is key—without it, you’ll have loose strands sticking out that won’t be gripped by the ferrule. If you’re working with very fine stranded wire (like 24-gauge), a smaller, more precise crimper is necessary, because larger crimpers can damage the tiny strands. I have a lot of hobbyist electricians who use the wrong tool for fine gauge wire and end up breaking strands during crimping— investing in a crimper with different die sets for different gauges solves that problem.

Now, when it comes to storing your cord ends and crimper, don’t overlook that. Cord ends can become bent or corroded if left in a damp environment, and a bent ferrule is impossible to crimp properly. Store your cord ends in a dry, airtight container, and keep your crimper in a case so the dies don’t get damaged. I always tell customers to label their crimpers and dies with the wire gauge and ferrule size they’re designed for—this prevents mixing up tools when you have multiple crimpers for different gauges.

At the end of the day, a good crimp is the difference between a connection that lasts years and one that fails in a few months. I’ve been supplying cord ends for over a decade, and I’ve learned that even experienced techs can make a simple mistake that leads to a bad crimp. If you’re not sure which crimper or cord end is right for your application, or if you have questions about a specific crimping job, reach out—my team and I are here to help. Whether you’re a small repair shop looking for bulk cord ends or a large industrial facility needing custom crimping solutions, we can match you with the right products to make your jobs go smoothly. Don’t take chances with your wiring connections—contact our team today to discuss your needs and find the right cord end and crimper for your work.

Sew-on Snap Button References

  1. Electrical Construction & Maintenance. (2022). Proper Crimping Techniques for Cord End Terminations. EC&M Magazine.
  2. National Electrical Manufacturers Association. (2021). Standards for Wire Ferrules and Crimp Tools. NEMA Publication.
  3. Automotive Industrial Electronics Association. (2020). Best Practices for Crimping in High-Vibration Environments. AIECA Technical Bulletin.
  4. Underwriters Laboratories. (2019). Safety Requirements for Cord End Termination Tools. UL 486C Standard.
  5. International Association of Electrical Inspectors. (2021). Common Mistakes in Cord End Crimping and How to Avoid Them. IAEI News.

Guangzhou Kunshuo International Trade Co., Ltd.
Guangzhou Kunshuo International Trade Co., Ltd. is one of the most professional cord end manufacturers and suppliers in China, featured by good service and competitive price. Please rest assured to buy or wholesale high quality cord end for sale here from our factory. For custom service, contact us now.
Address: Room 1415, 114-25, 114-24, 114-23, 114-22, 114-21, Xingang West Road, Guangzhou City, Guangdong Province, China
E-mail: jack@gdkunshuo.com
WebSite: https://www.jfbutton.com/