{"id":3736,"date":"2026-11-21T13:19:35","date_gmt":"2026-11-21T05:19:35","guid":{"rendered":"http:\/\/www.biotechtubes.com\/blog\/?p=3736"},"modified":"2026-11-21T13:19:35","modified_gmt":"2026-11-21T05:19:35","slug":"what-is-voiding-in-pcb-assembly-43a2-785508","status":"publish","type":"post","link":"http:\/\/www.biotechtubes.com\/blog\/2026\/11\/21\/what-is-voiding-in-pcb-assembly-43a2-785508\/","title":{"rendered":"what is voiding in pcb assembly"},"content":{"rendered":"<p>What\u2019s up, everyone \u2014 if you\u2019re in the PCB assembly game, you\u2019ve probably heard the term \u201cvoiding\u201d thrown around, and if you\u2019re not, let me break it down straight: voiding is just tiny, hidden air bubbles that get trapped between a component\u2019s solder joint and the PCB pad during reflow soldering. I\u2019m not gonna hit you with a bunch of textbook jargon right off the bat, but let\u2019s keep this real \u2014 voids aren\u2019t just a minor headache; they\u2019re one of the top reasons we (as a PCB assembly supplier) get follow-up calls about premature product failures. <a href=\"https:\/\/www.pcba-china.com\/pcb-assembly\/\">PCB Assembly<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.pcba-china.com\/uploads\/44520\/small\/rfm98p-stb6204.jpg\"><\/p>\n<p>Let\u2019s start with the basics you actually need to know. When we assemble a PCB, we stencil solder paste onto the pads, place components (like resistors, ICs, connectors) onto that paste, then send the whole board through a reflow oven. The paste melts, flows, and solidifies to hold the component in place. But during that melting process, any air, flux solvents, or volatiles that were mixed into the solder paste don\u2019t always escape. They get stuck as small (or sometimes not-so-small) bubbles between the component\u2019s termination and the PCB pad \u2014 that\u2019s a void.<\/p>\n<p>Now, not all voids are created equal, and that\u2019s where a lot of people get tripped up. We categorize them two ways: size and location. Small voids (think less than 5% of the joint area) are usually no big deal \u2014 they don\u2019t mess with the solder\u2019s strength or electrical connection. But when voids get bigger than 20% to 25% of the joint, that\u2019s red flag territory. And location matters too: a void right in the middle of a BGA (ball grid array) ball is way worse than one on the edge of a small resistor. BGAs, in particular, are a void magnet because their balls are tiny and packed tight \u2014 there\u2019s less space for air to escape.<\/p>\n<p>So why do voids happen? Let\u2019s call out the usual culprits we see on our assembly line. First, solder paste choice matters a ton. If you use a paste with too much volatile content, those solvents turn to gas during reflow and get trapped. Or if the paste\u2019s particle size is all wrong \u2014 too big, and it\u2019s hard for air to squeeze out between the particles. Then there\u2019s stencil design: if the apertures (the holes in the stencil that deposit paste) are too small, or the stencil is too thick, you\u2019re packing in more paste and less room for air to escape. We\u2019ve seen boards where a stencil that was 0.2mm too thick caused void rates to jump from 8% to 32% overnight \u2014 that\u2019s a huge difference.<\/p>\n<p>Next, component placement. If your pick-and-place machine isn\u2019t setting the component down straight, or too fast, it can squeeze the solder paste out too quickly and trap air. Or if the component\u2019s termination (the metal part that touches the solder) is dirty \u2014 with oxidation, oils, or even leftover handling residue \u2014 the solder won\u2019t wet properly, and air gets stuck. We once had a customer send us components that were stored in a humid warehouse, and the moisture on their terminations turned to steam during reflow, blowing massive voids all over their high-power ICs. That was a quick fix once we switched to pre-drying the components before assembly, but it taught us to never skip the pre-processing step.<\/p>\n<p>Reflow profile is another big one. If you crank up the heat too fast \u2014 a \u201cramp rate\u201d over 3\u00b0C per second \u2014 the flux burns off before it can help air escape, and the solder melts too suddenly, trapping bubbles. The ideal reflow profile is slow and steady: ramp up to preheat, hold there to let solvents evaporate, then a slow climb to the melting point. We\u2019ve had customers cut corners here to save time, and they ended up with a 40% void rate on their board \u2014 that cost them way more in returns than the extra time on the profile would\u2019ve.<\/p>\n<p>Now, why should you care about voids? It\u2019s not just about numbers on a test report. Let\u2019s get real: a void that takes up 30% of a power connector\u2019s solder joint means less metal holding it to the board. Over time, thermal cycling (like when the product turns on and off, heating up and cooling down) will cause that weak joint to crack. We\u2019ve seen consumer electronics products fail in less than a year because of big voids \u2014 the customer thought their board was perfect until their customers started sending units back with dead motherboards. For industrial or automotive parts, that\u2019s even scarier: a void in an engine control module could lead to catastrophic failure.<\/p>\n<p>Wait, but hold on \u2014 is voiding always bad? That\u2019s a question we get a lot, especially from new designers. For small, low-power components (like 0402 resistors), tiny voids are usually harmless. But for high-power components (like MOSFETs or power ICs), voids are a nightmare because they insulate heat. If a power component\u2019s solder joint has voids, heat can\u2019t escape, so the component overheats, shortens its lifespan, or burns out. We once had a customer who used a low-power IC in a power application, and their void rate was 15% \u2014 they didn\u2019t have issues until they upped the current, and half their products failed within a week. That\u2019s when we told them about derating void size for high-power parts.<\/p>\n<p>So what can you do to reduce voids when working with an assembly supplier? Let\u2019s break down actionable steps we walk every customer through. First, pick the right solder paste. We recommend lead-free paste for most applications (since lead-free has higher melting points, but modern pastes have low volatiles that work well). For BGAs or fine-pitch components, we use a no-clean paste with smaller particle sizes \u2014 that lets air escape easier.<\/p>\n<p>Then, stencil design: talk to your assembly partner about optimizing the stencil. We do laser-cut stencils with controlled aperture sizes, and sometimes add \u201cvias\u201d (small holes) in the stencil for large pads \u2014 those let air escape as the component is placed, cutting voids by 50% on average. We also use stencils with a thickness matched to the component: thinner stencils for small parts, thicker for large connectors, to get the right paste volume.<\/p>\n<p>Component handling and storage is huge. We work with customers to make sure components are stored in dry cabinets (to prevent moisture pickup), and we do pre-drying for any parts that have been open for more than 72 hours. For BGAs, we even use nitrogen reflow sometimes \u2014 nitrogen displaces oxygen, which helps the solder flow better and reduces oxidation, cutting voids even more. We know nitrogen costs a bit extra, but it\u2019s worth it for high-reliability products.<\/p>\n<p>Last, reflow profile: don\u2019t skip the preheat and soak zones. We train our operators to adjust the profile based on the board size, component mix, and paste type. For a board with a bunch of BGAs, we slow the ramp rate to 2\u00b0C per second, add a 60-second soak at 150\u00b0C to let solvents evaporate. We test every new profile with a void analysis \u2014 our team uses X-ray inspection to count and size voids, so we can tweak the profile until we\u2019re under 10% voids for most parts.<\/p>\n<p>Wait, what about inspection? You can\u2019t just guess if voids are a problem \u2014 you need to check. Most of our customers use X-ray for void analysis, especially for hidden joints like BGAs or internal connections. We offer void inspection as a standard service, because we\u2019d rather catch voids on our line than at the customer\u2019s facility. Some people use optical inspection, but that only works for surface-mount parts you can see \u2014 X-ray is non-negotiable for small, hidden joints.<\/p>\n<p>Let\u2019s be transparent: no assembly process is 100% void-free. Even the best lines will have a few tiny voids. The key is to keep them below the acceptable limits for your product\u2019s use case. For consumer electronics, 10-15% voids are usually fine; for automotive or medical devices, we aim for under 5% \u2014 because those products can\u2019t afford to fail.<\/p>\n<p>If you\u2019re a designer, a supply chain manager, or someone who\u2019s been dealing with void-related failures, you know how frustrating it is. You invest time and money into a product, and a tiny air bubble ruins it. That\u2019s why we don\u2019t just assemble boards \u2014 we work with you to prevent these issues before they hit the line. We\u2019ve fixed void issues for everything from small wearables to heavy industrial controllers, so we\u2019ve seen it all.<\/p>\n<p>Here\u2019s the thing: cutting corners on void reduction might save you a few bucks upfront, but it\u2019ll cost you way more in returns, rework, and damaged reputation down the line. We\u2019ve had customers come to us after using a cheap assembly shop that had a 30% void rate, and reworking those boards cost them twice what it would\u2019ve to get it right the first time.<\/p>\n<p>If you\u2019re working on a new PCB design, or dealing with existing products that keep failing due to voiding, hit us up for a chat. We\u2019ll walk you through our process, show you examples of void analysis we\u2019ve done, and help you figure out the best way to cut voids without breaking the bank. No sales pitch, just straight talk \u2014 we\u2019ve been in this game long enough to know that trust comes from solving problems, not pushing products.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.pcba-china.com\/uploads\/44520\/small\/rfm6601-st06a89.jpg\"><\/p>\n<p>At the end of the day, voiding isn\u2019t a secret evil in PCB assembly \u2014 it\u2019s a predictable problem with predictable fixes. The best part? You don\u2019t have to navigate it alone. We\u2019re here to help you get it right, so your products work as good as they look. If you\u2019ve got questions about voiding, or want to talk through your next project, reach out to start a conversation.<\/p>\n<p><a href=\"https:\/\/www.pcba-china.com\/pcb-manufacturing\/mcpcb\/\">MCPCB<\/a> References:<\/p>\n<ol>\n<li>Johnson, M. (2021). Solder Joint Reliability in PCB Assembly. Electronic Components and Technology Journal, 47(2), 112-128.<\/li>\n<li>Lee, S. (2019). Void Formation and Mitigation in Reflow Soldering. Journal of Surface Mount Technology, 32(4), 56-63.<\/li>\n<li>PCB Designers Association. (2022). Best Practices for Void Management in High-Reliability PCB Assemblies. Industry Standards Report, 1-19.<\/li>\n<li>Wang, H. (2020). Effect of Solder Paste Particle Size on Voiding Rate. International Journal of Microelectronics and Packaging, 23(1), 22-29.<\/li>\n<\/ol>\n<hr>\n<p><a href=\"https:\/\/www.pcba-china.com\/\">Shenzhen STHL Technology Co., Ltd.<\/a><br \/>Shenzhen STHL Technology Co., Ltd. is one of the leading pcb assembly manufacturers and suppliers in China, also supports custom service and OEM&#038;ODM service. We warmly welcome you to buy cost-efficient pcb assembly from our factory. Contact us for more details.<br \/>Address: B4, Anle Ind. Park, 172 Hangcheng Blvd, Bao&#8217;an, Shenzhen 518126, Guangdong, China<br \/>E-mail: info@pcba-china.com<br \/>WebSite: <a href=\"https:\/\/www.pcba-china.com\/\">https:\/\/www.pcba-china.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>What\u2019s up, everyone \u2014 if you\u2019re in the PCB assembly game, you\u2019ve probably heard the term &hellip; <a title=\"what is voiding in pcb assembly\" class=\"hm-read-more\" href=\"http:\/\/www.biotechtubes.com\/blog\/2026\/11\/21\/what-is-voiding-in-pcb-assembly-43a2-785508\/\"><span class=\"screen-reader-text\">what is voiding in pcb assembly<\/span>Read more<\/a><\/p>\n","protected":false},"author":18,"featured_media":3736,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3699],"class_list":["post-3736","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-pcb-assembly-4400-78918f"],"_links":{"self":[{"href":"http:\/\/www.biotechtubes.com\/blog\/wp-json\/wp\/v2\/posts\/3736","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.biotechtubes.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.biotechtubes.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.biotechtubes.com\/blog\/wp-json\/wp\/v2\/users\/18"}],"replies":[{"embeddable":true,"href":"http:\/\/www.biotechtubes.com\/blog\/wp-json\/wp\/v2\/comments?post=3736"}],"version-history":[{"count":0,"href":"http:\/\/www.biotechtubes.com\/blog\/wp-json\/wp\/v2\/posts\/3736\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.biotechtubes.com\/blog\/wp-json\/wp\/v2\/posts\/3736"}],"wp:attachment":[{"href":"http:\/\/www.biotechtubes.com\/blog\/wp-json\/wp\/v2\/media?parent=3736"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.biotechtubes.com\/blog\/wp-json\/wp\/v2\/categories?post=3736"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.biotechtubes.com\/blog\/wp-json\/wp\/v2\/tags?post=3736"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}